Your daily dose of photovoltaic technology developments and solar news

This article highlights an alternative method for increasing short-wavelength external quantum efficiency (EQE) and hence overall conversion efficiency of mc-Si PV modules via luminescent down-shifting (LDS), a technique originally proposed by Hovel et al. [1] in 1979. The potential for efficiency enhancement via LDS has been either predicted or measured for a wide range of PV technologies (see [2] for a review). However, in this article, we will highlight how LDS can be incorporated into the existing encapsulation layer, avoiding any modification to well-established solar cell manufacturing processes and thus offering the potential of a production-ready technology.

This paper, the fourth in a series covering cost modelling studies for photovoltaics [1-3], examines a new approach to module assembly based on the concept of ‘supersized' 1kW PV modules. Using supersized modules (1.6m × 3.8m) and integrated microinverters, this novel approach has the estimated potential to save utility solar installations nearly $0.50/Watt. The paper will conclude with a detailed cost and resource case study comparing two 40MW module lines, one employing ‘solar breeder' technology and the other producing conventional-sized modules.

This paper presents fluorescence detection as a new tool for the investigation of the degradation of EVA. The superior sensitivity of the set-up contained herein allows an early assessment of the changes of the EVA after only 20 hours of damp-heat exposure. A newly developed scanning system allows the spatially resolved inspection of entire PV modules. Degradation of the encapsulants was detectable after two years' outdoor exposure, as was the effect of cracks in c-Si cells, which coincide well with cracks made visible by electroluminescence.

Solar enterprises will each be faced with the occasional surplus or lack of solar modules in their lifetimes. In these instances, it is useful to adjust these stock levels at short notice, thus creating a spot market. Spot markets serve the short-term trade of different products, where the seller is able to permanently or temporarily offset surplus, while buyers are able to access attractive offers on surplus stocks and supplement existing supply arrangements as a last resort.

Cell interconnection is recognized as the most critical process with respect to module production yield. If the process is not carefully controlled, cell cracking and subsequent breakage may occur. Many manufacturers promise breakage rates below 0.3-0.5% on their tabber-stringers, which applies for cells above 160-180µm thickness that are free from initial cracks. In real production, this figure strongly depends on materials, process parameters and throughput. This paper outlines some approaches that should be taken to avoid high levels of breakage in the cell interconnection process.

Solar enterprises will each be faced with the occasional surplus or lack of solar modules in their lifetimes. In these instances, it is useful to adjust these stock levels at short notice, thus creating a spot market. Spot markets serve the short-term trade of different products, where the seller is able to permanently or temporarily offset surplus, while buyers are able to access attractive offers on surplus stocks and supplement existing supply arrangements as a last resort.

Encapsulant materials used in PV modules serve multiple purposes. They physically hold components in place, provide electrical insulation, optically couple superstrate materials (e.g., glass) to PV cells, protect components from mechanical stress by mechanically de-coupling components via strain relief, and protect materials from corrosion. To do this, encapsulants must adhere well to all surfaces, remain compliant, and transmit light after exposure to temperature, humidity, and UV radiation histories. Encapsulant materials by themselves do not completely prevent water vapour ingress [1-3], but if they are well adhered, they will prevent the accumulation of liquid water providing protection against corrosion as well as electrical shock. Here, a brief review of some of the polymeric materials under consideration for PV applications is provided, with an explanation of some of their advantages and disadvantages.

This paper describes a methodology used to establish reliability of a CIGS thin-film photovoltaic module component based on identification of a failure mode through product thermal-cycling. The initial observation of the failure is described as part of a larger reliability program that progresses from failure mode and effect analysis through a test-to-failure program that has an objective of understanding the ultimate consequence of specific applied stresses on product performance. Once the specific failure mode was discovered, four means of characterizing the mode were applied and are discussed: tensile testing and material analysis, computer modelling, coupon rapid thermal cycling, and mechanical fatigue testing. This work identified the relevant root cause for failure and facilitated a materials change, which itself was subjected to an accelerated testing program to quantify the improvement and determine success of the design. The means of verifying success included meeting an endurance thermal-cycle limit for a collection of samples and subjecting corrected designs to a mechanical fatigue test, where the correlation between thermal cycle and mechanical fatigue were compared using Weibull analysis.

Photovoltaic modules are designed to meet the reliability and safety requirements of national and international test standards. Qualification testing is a short-duration (typically, 60-90 days) accelerated testing protocol, and it may be considered as a minimum requirement to undertake reliability testing. The goal of qualification testing is to identify the initial short-term reliability issues in the field, while the qualification testing/certification is primarily driven by marketplace requirements. Safety testing, however, is a regulatory requirement where the modules are assessed for the prevention of electrical shock, fire hazards, and personal injury due to electrical, mechanical, and environmental stresses in the field. This paper examines recent reliability and safety studies conducted at TÜV Rheinland PTL’s solar module testing facility in Arizona.

Solar enterprises will each be faced with the occasional surplus or lack of solar modules in their lifetimes. In these instances, it is useful to adjust these stock levels at short notice, thus creating a spot market. Spot markets serve the short-term trade of different products, where the seller is able to permanently or temporarily offset surplus, while buyers are able to access attractive offers on surplus stocks and supplement existing supply arrangements as a last resort.